WattStep Group
[ ← CAPABILITIES ]

Axial Flux Motors

The future of electric drive

The next generation of electric machines is axial, and it is already here. Our standard motors deliver high torque density in a short axial package, verified with electromagnetic and thermal simulation, and designed without heavy rare earth metals.

Axial flux motor without heavy rare earth metals

WattStep integrated axial flux motor and inverter unit
SpecificationAFMPM-I400AFMPM-F400
Peak torque (Nm)394.9585
Continuous torque (Nm)223.6427
Peak power (kW)227.6175.4
Continuous power (kW)12999
Voltage (VDC)400400
Dry weight (kg)2424
Peak torque density (Nm/kg)16.4524.4
Maximum speed (rpm)9 0009 000
CoolingOilOil

[ REF: AXF-DATA / WATTSTEP ]

Torque and power density

WattStep I400

Peak torque density
16.5 Nm/kg
Peak power density at 800 V
9.5 kW/kg

WattStep F400

Peak torque density
24.4 Nm/kg
Peak power density at 400 V
7.3 kW/kg

Peak figures per kg of motor mass. I400 power at 800 V; F400 power at 400 V.

[ ONE INTEGRATED UNIT ]

A simple installation

Most axial flux makers sell a motor and leave you to find, fit and tune an inverter. The Nytron i4040 sits on the face of the motor and shares its cooling, so you connect DC power, a CAN cable and one cooling circuit, for both.

[ THE BUILDING BLOCKS ]

01

One cooling circuit

One cooling loop, oil or water-glycol, is integrated in both motor and inverter. No second cooling system to design, plumb or maintain.

02

No separate inverter box

The Nytron i4040 sits on the face of the motor. Nothing extra to place, mount or protect inside the machine.

03

No three-phase cabling

The phase connections live inside the unit. You route DC and CAN, not three thick high-current cables.

04

No cross-supplier tuning

Motor and inverter are tuned together by the same team that built both. One supplier to call, one system to validate.

[ MODULAR PLATFORM ]

Stackable for more power

Like plates on a barbell, several units mount in series on a shared shaft to reach the torque or power the job needs. Even three stacked units, three times the power, are shorter than a single radial motor in the same power class.

Three WattStep axial flux motors stacked upright, held together by steel tie rods
Three AFMPM-I400 units on one shaft: 683 kW peak, 400 mm long
ConfigurationLengthPeak power @ 800 VDCWeight
1 × AFMPM-I400105 mm228 kW24 kg
2 × AFMPM-I400253 mm455 kW48 kg
3 × AFMPM-I400400 mm683 kW72 kg

AFMPM-I400 figures. Peak power at 800 V with an 800 V-capable inverter; with today's 400 V Nytron, peak power is half. Stacked units are driven by an external inverter sized for the combined power. The built-in Nytron drives a single unit.

Where it fits

Our motors make the biggest difference where power density, weight and simple installation decide the design. These are the segments where that matters most.

01

Off-highway and construction

Tiltrotators, crane rotators, harvester heads, compact track loaders

Why WattStep

  • High torque density
  • Integrated inverter
  • Integrated

02

Marine

Thrusters, trim systems, electric propulsion

Why WattStep

  • High torque density
  • Low axial length
  • Low rpm

03

Automotive

Combustion-to-electric conversions, sports cars, racing, high-performance hybrids

Why WattStep

  • High power density
  • Low volume
  • Integrated inverter

04

Aerospace and drones

Electric aircraft, heavy-lift drones, airships

Why WattStep

  • Low weight
  • Low axial length

[ QUESTIONS & ANSWERS ]

Frequently asked questions

An axial flux motor directs magnetic flux parallel to the shaft. Its disc-shaped geometry supports a short axial package. The WattStep platform includes the AFMPM-I400 and AFMPM-F400 standard axial flux motors, with specifications listed in the comparison table above.

Yes. The motor and inverter can be installed and used as separate components rather than as an integrated unit. The motor still requires a compatible inverter, with suitable electrical connections, control and cooling for the application. In the integrated configuration, the motor and silicon carbide inverter form one unit with internal phase connections and a cooling circuit integrated in both parts. The motor uses direct oil cooling. Other cooling media can be used in a separate circuit connected through a heat exchanger, while oil remains the coolant in direct contact with the motor.

The motor can also operate at 800 V when paired with an inverter rated for that voltage. The standard Nytron i4040 is rated at 400 VDC, so motor operation at 800 V requires a suitable alternative inverter.

Consider the required torque, speed range, duty cycle, cooling and installation space. WattStep can help you choose the appropriate standard unit for your application. Yes. Alongside our standard motor and inverter platform, WattStep can handle special orders for requirements outside the existing platform. These projects are separate from our standard products and are discussed individually.

Erik Strigén, Business Developer at WattStep

[ FIRST CONVERSATION ]

Book a meeting

Erik Strigén, Business Developer, takes the first conversation about your drivetrain, timeline and requirements. Pick a slot directly in his calendar.

Book a meeting with Erik